-
2
-
11
-
14
-
15
-
0
-
70The elements contained in element set ErrElemExcessDistortion-Step1 have distorted excessively. The elements in element set ErrElemZeroALEMass-Step1 have zero or negative mass. Print-out suppressed for subsequent distorted elements There are a total of 4346 excessively distorted elements The elements contained in element set ErrElemExcessDistortion-Step1 have distorted excessively. Abaqus/Explicit Analysis exited with an error - Please see the status file for possible error messages if the file exists.
-
3求助,我在做abaqus分析时用到了ALE,第一次用,出现了一下问题,请问怎么解决 Adaptive meshing is not supported for elements used with the hyper or viscohyper material model when enhanced hourglass control is used. Domain name: assembly__pickedset49
-
0
-
4
-
2
-
0做的拉伸模拟,输出的场变量是s22和PEEQ
-
0
-
7The elements contained in element set ErrElemExcessDistortion-Step1 have distorted excessively. There is only one excessively distorted element The ratio of deformation speed to wave speed exceeds 1.0000 in at least one element. This usually indicates an error with the model definition. Additional diagnostic information may be found in the message file. The elements contained in element set ErrElemExcessDistortion-Step1 have distorted excessively. Abaqus/Explicit Analysis exited with an error - Please see the status file for possible error messages if the file exists.
-
2我用elcopy法导入inp文件的时候,提示我单元集不存在,但我明明设置了集合啊
-
1
-
2
-
3
-
2分析步第一部焊接部计算时间太长,计算了3000多步,还没结束 。
-
3
-
3
-
1请问佬们,这个应该怎么解决 output request status is not available for element type r3d4
-
7在ABAQUS静力通用分析部中导入预定义温度场以后,算出的热应力结果为0
-
9ABAQUS中,两个独立实体在装配中合并为一个实体,合并后的实体各部分材料属性怎么变成一个了
-
1
-
5
-
0我是小白,想请教各位大神指点。我在网上找人代下了2023abaqus后发现计算不了,百度说需要下载关联程序,然后又代下了vs和fortran。不过现在在学习视频时发现仍然计算不了,比如说视频里运用的UMESHMOTION磨损子程序,我跟着做但是没有最后的计算过程是因为我没有录取这种模块程序吗,vs和fortran只是一个接口吗?这种磨损子程序应该怎么录入软件
-
22
-
1
-
0网上搜了一下但是没找到具体教程,希望大佬赐教
-
2
-
9RT,建立了一个高85米的地层模型,里面挖了一根直径一米的钢管,分别对地层和钢管进行了网格划分。因为钢管太细导致钢管的网格和底层相比特别小,运行结果就不收敛,这种情况怎么办?
-
1我这里有一个警告信息,但是我不会解决,求助一下各位佬们 TYPE=BELOW MIN mass scaling will be ignored for rigid elements
-
0
-
0我需要根据频率输出结果,我设置稳态动力学分析步,然后在一个面施加电势边界,这个电势是否会随着分析步里面的频率改变而改变频率?
-
0
-
4
-
5遇到些问题,想请教一下
-
1
-
0在网上找了很长时间也没找到关于体力方面的详细介绍,有人说体力是材料密度乘加速度,这样的话假如我材料密度7.85e-9,,想用体力代替重力,体力就应该输入-7.85e-9×9810的计算结果?但我的模型在如此设置后计算不收敛,反倒把这个数值设置在0.1左右时能勉强收敛。
-
2
-
7
-
2
-
0
-
9
-
0兄弟们 想建立一个粘弹性边界,但是没有一点头绪,有么有大佬给点思路